Quick Answer: How Long Does It Take Thompson’S Water Seal To Cure?

What happens if it rains after applying Thompson’s Water Seal?

Rain will damage the finish of any wet sealer with linseed oil or mineral oil in it.

Because it forms a coating, it takes several hours to “set up” (dry) and during that time the sealer is vulnerable..

How often should you apply Thompson’s Water Seal?

every one to three yearsApplying a sealer and/or stain typically is recommended every one to three years, depending on the finishing product, deck use, weather conditions, and sun exposure. All Thompson’s WaterSeal products are DIY-friendly, and most need only a single application on a clean, dry deck.

What is the longest lasting deck sealer?

Longest-Lasting Seal. Olympic Maximum Waterproofing Sealant. … Best Overall. Seal-Once Marine Premium Wood Sealer. … Easiest Application. Eco Advance Exterior Wood Waterproofer. … Best Value. Olympic Smartguard Concentrated Sealant. … Longest-Lasting Seal. … Best Overall. … Easiest Application. … Best Value.More items…

What temperature do you apply Thompson’s Water Seal?

Be sure that both surface and air temperatures are above 50°F during application and remain above 40°F for 48 hours after application. Do not apply product if rain is forecasted within 24 hours of application.

Can you spray Thompson’s water sealer?

The manufacturer of Thompson Water Seal recommended that you use their product with a plastic sprayer with a brass wand, such as our Chapin Premier sprayer. … Once you are done with the product, it is recommended that you run mineral spirits through the sprayer and then water to clean it.

Can you apply Thompson’s Water Seal over paint?

The hydrophobic properties of Water Seal will negatively affect the adhesion of any paint applied over it. Can Water Seal be applied to painted surfaces? No. Water Seal can only be used on bare and uncoated brick, stone or concrete.

Can I mix stain and Thompson’s Water sealer?

As long as it’s all oil based you should be able too. But if it’s a solid color stain it might turn a little transparent if mixed with the sealer…..just give it a try on a scrap piece. Bingo. As long as they use the same solvents, it should be fine.

How many coats of Thompson Water Seal do I need?

2 coatsshake the can vigorously before use. Thompson’s Water seal has a slightly milky appearence in the can,but clears quickly upon application. For best results ensure the surface is as dry as possible. Apply 2 coats using brush,roller or sprayer.

Is it better to stain or seal a deck?

Many deck companies recommend using a combination stain/sealer product, which is basically a sealer with pigment added. The advantage of this, they say, is the sealer provides additional protection against water and weather damage, while the stain helps reduce fading from UV rays.

What is the best way to apply deck sealer?

Apply the deck sealer with a natural bristle brush. A roller is faster, but brushing helps force the sealer into open pores and grain. Make sure to get the sealer into joints where two boards butt together. Apply the deck sealer to three or four boards at once, working their entire length.

Is Thompson Water Seal oil or water based?

Thompson’s® WaterSeal® Penetrating Timber Oil is an oil-based product that provides protection by penetrating into wood pores and sealing out water infiltration. Thompson’s® WaterSeal® Waterproofing Stains are water-based products that have film-forming properties to protect the wood by repelling water.

Does Thompson Water Seal work?

5.0 out of 5 stars Love Thompson’s Water Seal with the harvest gold color! Basically, it takes your weather worn fence and restores it back to almost new looking boards, plus protecting it from the elements. I used my spray gun to apply, and a little goes a long way. Obviously, you can use a brush to apply it as well.

What is the best way to apply Thompson’s Water sealer?

Apply by brush, roller, dipping, or sprayer. A garden “pump-up” style sprayer is the simplest method. If over applied, remove excess before it dries by redistributing to dry areas or wiping off.

Can you apply Thompson’s Water Seal to wet wood?

Thompson’s® WaterSeal® Waterproofing Stains can be applied to damp wood, so you only have to wait about two hours to begin applying stain. Some of our other products require that the wood dry for 48 hours before applying a deck coating.