Quick Answer: How Does The Automatic Oiler Work On A Chainsaw?

How do you manually oil a chainsaw chain?

The steps are quick and easy:Set your chainsaw on a level surface, bar side down so that it lays flat.Allow a minute for the oil to settle, then unscrew the cap to the saw’s bar and chain oil reservoir.Using a small funnel, slowly pour the bar and chain oil into the reservoir, taking care not to overfill.More items….

How do I stop my chainsaw oil from leaking?

If you need to keep oil in the tank, then the best way to vent your chainsaws oil tank is to lay the chainsaw on its side with the oil cap pointing upwards and open the cap slightly. This will reduce the pressure from building up in the oil tank during fluctuations in temperature.

How do you adjust a chainsaw Oiler?

To increase the oil flow, turn the automatic oiler adjustment screw counterclockwise. To decrease oil flow, turn the automatic oiler adjustment screw clockwise. While always wearing heavy work gloves, grasp the chain and pull it towards the nose of the chainsaw to ensure that the chain moves freely.

Can you adjust the Oiler on a Stihl chainsaw?

Turn the chainsaw off to adjust the oiler. Insert a small flat-head screwdriver into the oil adjustment screw on the underside of the chainsaw. Turn the screw clockwise to increase oil flow or counterclockwise to decrease the oil flow.

How much oil should my chainsaw use?

When to Oil Gas chainsaws use about one tank of bar and chain oil for every tank of fuel, so fill the reservoir every time you fill the tank.

What happens if you run a chainsaw without bar oil?

The links wear out and can break, running your saw without bar oil will increases the chances of a break. Chain oil helps everything move freely but it also helps cool the chain. … A chain can also just seize in the bar which can cause damage to the engine in addition to a new bar and chain.

How long should you let a chainsaw warm up?

About 30 secondsAbout 30 seconds with a few revs.

What should you not cut with a chainsaw?

Don’t ever run while carrying a chainsaw. Do try to avoid cutting with the blade tip, this will also help avoid kickback. Do try cut below shoulder height wherever possible. This will keep a chainsaw away from your face in the event of kickback.

How long can you run a chainsaw?

It ultimately comes down to the factors listed above (especially maintenance). That being said, you can expect a quality chainsaw to last you at least 10 years or more. But if you take care of it, I know people who have saws that have lasted 20-30 years and even longer.

Why is my chainsaw bar smoking?

The most likely causes of smoking and overheating are a lack of air and/or a lack of lubrication to the engine or the chain saw chain guide bar.

How does the oiler work on a chainsaw?

Specially engineered chainsaw bar oil goes into the oil reservoir. … As you throttle up, a worm drive engages the pump to send oil through a port that releases onto the bar. As the chain moves across the bar, it distributes the oil across the surface, reducing the friction and the heat that occurs when cutting.

Why does my chainsaw blade get dull so fast?

You may be putting to steep of an angle on the cutters, which will dull quickly. You’re rakers may be too far down, which will contribute to a quick dulling chain. You may be cutting dirty wood. You may be slightly touching the ground with the tip of the bar.

How do you adjust a chainsaw High Low?

Carburetor Adjustment ProcedureBefore you start the saw, locate a small flat-bladed screwdriver. … Begin by checking the saw’s air filter. … Check the fuel level. … Start the engine and warm it up. … Begin by setting the idle speed. … Set the low speed fuel adjustment. … Go back to step (4) and reset the idle speed.More items…

How tight should the chain be on a chainsaw?

A properly-tensioned chainsaw chain should still be just a little loose on the chainsaw guide bar, but the chain needs to be tight enough that you can’t pull the drive links out of the bar nose.

Should I run my chainsaw dry?

Never run your chainsaw dry. You should instead use a quality gas stabilizer. A stabilizer will keep your fuel fresh and protect your fuel system from damage caused by stale gas.

Why is my chainsaw not oiling the chain?

It’s simple to check whether or not the oiler works properly: Hold the chainsaw over a flat surface, such as a tree stump, engage the throttle and look for oil drops coming from the spinning chain. The absence of these drops may mean that the oil port is blocked. Clearing a blocked oil port isn’t difficult.

Why is my chainsaw burning the wood?

Scorching and smoking a blunt chain and lack of lubrication. Finer sawdust is an indication that the chain is becoming blunt. Before putting a saw away after cutting particularly after cutting messy timber it should always be cleaned, side plate off and cleaned underneath, chain bar cleaned and chain sharpened.